ZyXEL Communications Network Router NOT AVAILABLE Instrukcja Użytkownika Strona 81
- Strona / 300
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 9 Wireless LAN Profiles
NXC CLI Reference Guide
81
2g-support-speed {disable |
wlan_2g_support_speed}
Disables or sets the 2.4 GHz support rate.
The default is 1.0~54.0.
2g-mcs-speed {disable |
wlan_mcs_speed}
Disables or sets the 2.4 GHz HT MCS rate.
The default is 0~15.
2g-multicast-speed
wlan_2g_support_speed
When you disable
multicast to unicast, use this
command to set the data rate
{ 1.0 | 2.0 | … } in
Mbps for 2.4 GHz multicast traffic.
5g-basic-speed wlan_5g_basic_speed Sets the 5 GHz basic band rate.
The default is 6.0 12.0 24.0.
5g-support-speed {disable |
wlan_5g_support_speed}
Disables or sets the 5 GHz support rate.
The default is 6.0~54.0.
5g-mcs-speed {disable |
wlan_mcs_speed}
Disables or sets the 5 GHz HT MCS rate.
The default is 0~15.
5g-multicast-speed
{wlan_5g_basic_speed}
When you disable
multicast to unicast, use this
command to set the data rate
{ 6.0 | 9.0 | … } in
Mbps for 5 GHz multicast traffic.
tx-mask chain_mask Sets the outgoing chain mask rate.
rx-mask chain_mask Sets the incoming chain mask rate.
[no] htprotection Activates HT protection for this profile. Use the no
parameter to disable it.
By default, this is disabled.
output-power wlan_power Sets the output power for the radio in this profile.
The default is 100%.
[no] ssid-profile
wlan_interface_index ssid_profile
Assigns an SSID profile to this radio profile. Requires an
existing SSID profile. Use the no parameter to disable it.
exit Exits configuration mode for this profile.
show wlan-monitor-profile {all |
monitor_profile_name}
Displays all monitor profiles or just the specified one.
wlan-monitor-profile rename
monitor_profile_name1
monitor_profile_name2
Gives an existing monitor profile
(monitor_profile_name1) a new name
(monitor_profile_name2).
[no] wlan-monitor-profile
monitor_profile_name
Enters configuration mode for the specified monitor
profile. Use the no parameter to remove the specified
profile.
[no] activate Makes this profile active or inactive.
By default, this is enabled.
scan-method scan_method Sets the channel scanning method for this profile.
[no] 2g-scan-channel
wireless_channel_2g
Sets the broadcast band for this profile in the 2.4 Ghz
frequency range. Use the no parameter to disable it.
[no] 5g-scan-channel
wireless_channel_5g
Sets the broadcast band for this profile in the 5 GHz
frequency range. Use the no parameter to disable it.
scan-dwell <100..1000> Sets the duration in milliseconds that the device using
this profile scans each channel.
exit Exits configuration mode for this profile.
Table 31 Command Summary: Radio Profile (continued)
COMMAND DESCRIPTION
- NXC Series 1
- CLI Reference Guide 1
- IMPORTANT! 2
- Contents Overview 3
- Table of Contents 10
- NXC CLI Reference Guide 10
- Table of Contents 11
- Chapter 34 12
- Chapter 35 12
- CHAPTER 1 15
- 1.2.1 Console Port 16
- Figure 3 Console 17
- Table 2 Console 18
- LABEL DESCRIPTION 18
- 1.2.3 Telnet 20
- 1.2.4 SSH (Secure SHell) 20
- 1.4.1 Background Information 21
- 1.4.2 Command Input Values 21
- 1.5 CLI Modes 22
- 1.6 Shortcuts and Help 23
- 1.7 Input Values 26
- 1.9 Logging Out 29
- CHAPTER 2 31
- 2.1.1 Debug Commands 33
- CHAPTER 3 35
- Chapter 3 Object Reference 36
- CHAPTER 4 37
- RAM size, and serial number 38
- Chapter 4 Status 39
- Chapter 4 Status 40
- CHAPTER 5 41
- Chapter 5 Registration 42
- 5.2 Registration Commands 43
- 5.3 Country Code 44
- Chapter 5 Registration 45
- CHAPTER 6 49
- Chapter 6 Interfaces 52
- 6.2.2 DHCP Setting Commands 53
- Chapter 6 Interfaces 57
- 6.4 Port Commands 59
- 6.5 Port Role Commands 60
- CHAPTER 7 65
- Chapter 7 Route 68
- 7.3 IP Static Route 69
- 7.4 Static Route Commands 70
- Chapter 7 Route 71
- CHAPTER 8 73
- 8.2 AP Management Commands 74
- Chapter 8 AP Management 75
- Chapter 8 AP Management 76
- CHAPTER 9 77
- 9.3 SSID Profile Commands 83
- 9.3.1 SSID Profile Example 84
- CHAPTER 10 89
- Chapter 10 Rogue AP 90
- Chapter 10 Rogue AP 91
- Denial of Service attack 92
- CHAPTER 11 93
- CHAPTER 12 95
- 12.2.1 DCS Examples 96
- CHAPTER 13 99
- CHAPTER 14 103
- Chapter 14 Dynamic Guest 104
- Chapter 14 Dynamic Guest 105
- CHAPTER 15 107
- 15.2 Zone Commands Summary 108
- 15.2.1 Zone Command Examples 109
- Chapter 15 Zones 110
- CHAPTER 16 111
- 16.2 ALG Commands 112
- 16.3 ALG Commands Example 112
- CHAPTER 17 113
- Chapter 17 Captive Portal 114
- CHAPTER 18 117
- Chapter 18 RTLS 118
- CHAPTER 19 119
- 19.2 Firewall Commands 120
- Chapter 19 Firewall 121
- 19.2.1 Firewall Sub-Commands 122
- 19.3 Session Limit Commands 124
- means all IP 125
- means all users 125
- Chapter 19 Firewall 126
- CHAPTER 20 127
- 20.2.2.1 Rule Sub-commands 129
- Chapter 20 Application Patrol 130
- CHAPTER 21 137
- 21.2.3 White and Black Lists 140
- Chapter 21 Anti-Virus 141
- Chapter 21 Anti-Virus 142
- Table 76 Update Signatures 142
- 21.4 Anti-virus Statistics 143
- CHAPTER 22 145
- 22.3 IDP Profile Commands 146
- Chapter 22 IDP Commands 147
- old_profile new_profile 147
- Chapter 22 IDP Commands 148
- 22.3.6 Signature Search 153
- If you 155
- 22.4 IDP Custom Signatures 156
- fragoffset_rel: 159
- 22.5 Update IDP Signatures 160
- 22.6 IDP Statistics 161
- CHAPTER 23 163
- 23.1.1 Before You Begin 164
- Chapter 23 Device HA 165
- Chapter 23 Device HA 168
- CHAPTER 24 169
- 24.2.1 User Commands 170
- 24.2.2 User Group Commands 171
- 24.2.3 User Setting Commands 171
- 24.2.4 MAC Auth Commands 173
- Chapter 24 User/Group 174
- Chapter 24 User/Group 175
- CHAPTER 25 177
- Chapter 25 Addresses 180
- CHAPTER 26 181
- ICMP_ECHO to SG1 183
- Chapter 26 Services 184
- CHAPTER 27 185
- Chapter 27 Schedules 186
- Table 109 schedule Commands 186
- CHAPTER 28 187
- Chapter 28 AAA Server 192
- CHAPTER 29 193
- 29.3 test aaa Command 195
- CHAPTER 30 197
- CHAPTER 31 199
- Chapter 31 ENC 201
- Chapter 31 ENC 202
- CHAPTER 32 203
- Chapter 32 Certificates 205
- Chapter 32 Certificates 206
- CHAPTER 33 207
- Chapter 33 System 208
- 33.3 Host Name Commands 209
- 33.4 Time and Date 209
- 33.4.1 Date/Time Commands 210
- 33.5 Console Port Speed 211
- 33.6 DNS Overview 211
- 33.6.2 DNS Command Example 212
- CHAPTER 34 213
- 34.3 HTTP/HTTPS Commands 214
- 34.4 SSH 216
- 34.5 Telnet 217
- 34.6 Telnet Commands 218
- 34.7 Configuring FTP 219
- 34.8 SNMP 220
- 34.8.3 SNMP Commands 221
- 34.9 Language Commands 222
- CHAPTER 35 223
- Chapter 35 File Manager 224
- Chapter 35 File Manager 225
- 35.6 FTP File Transfer 228
- Figure 23 Firmware Damaged 232
- Figure 24 Enter Debug Mode 232
- Figure 34 Restart Complete 236
- Figure 38 Enter Debug Mode 238
- Figure 44 Startup Complete 240
- CHAPTER 36 241
- 36.1.1 Log Entries Commands 242
- 36.1.2 System Log Commands 242
- 36.1.3 Debug Log Commands 243
- Chapter 36 Logs 247
- Chapter 36 Logs 248
- CHAPTER 37 249
- 37.1.3 Session Commands 250
- Chapter 37 Reports and Reboot 252
- 37.3 Reboot 254
- CHAPTER 38 255
- Chapter 38 Session Timeout 256
- CHAPTER 39 257
- Chapter 39 Diagnostics 258
- CHAPTER 40 259
- CHAPTER 41 261
- Chapter 41 Maintenance Tools 262
- 41.1.1 Command Examples 263
- Chapter 41 Maintenance Tools 265
- CHAPTER 42 267
- 42.3 Application Watchdog 268
- Chapter 42 Watchdog Timer 269
- Chapter 42 Watchdog Timer 270
- CHAPTER 43 271
- 43.3 CAPWAP Client Commands 272
- 43.4 DNS Server Commands 274
- List of Commands 277
- List of Commands 279
Powiązane produkty i podręczniki dla Oprogramowanie ZyXEL Communications Network Router NOT AVAILABLE
Oprogramowanie ZyXEL NSA210 Instrukcja Użytkownika
(576 strony)
(576 strony)
Oprogramowanie ZyXEL IES-5005 Instrukcja Użytkownika
(100 strony)
(100 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.150 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji